How Much To Fix A Window Motor

Download Article

Download Commodity

If one of the power windows in your vehicle fails to office, it may be the result of a broken power window motor. If you accept identified the motor every bit the culprit, replacing it is fairly directly forward, though information technology tin be time consuming. It is recommended that you review a service manual specific to your vehicle when replacing the motor, as the methods used to disassemble car doors can vary from vehicle to vehicle.

1
Remove the interior door panel. Most interior door panels are held in place with plastic interior fasteners. You can remove these fasteners past pulling on them until they pop out of their holes. Interior panels may also exist held on with metal or plastic screws or even bolts.^[i]
- If you can't easily identify what kind of fasteners are on your door panel, refer to the vehicle's service manual.
- Turn screws or bolts counter clockwise to loosen them, and so pull the panel backward off of the door.
2
Gently remove the plastic door cover. Beneath the door console you will find a thin, translucent layer of plastic. This cover protects the interior of the vehicle from any water that may splash into the door from above and below. Carefully pull the door off of the viscous portions that secure information technology.^[2]
- Endeavor not to tear the cover as yous will need to reinstall it after replacing the window motor.
- Replacement covers can be purchased at your local auto parts store.
Advertising
3
Locate the window mounting bolts. Depending on the design of your door, there are a few different places the window mounting bolts may be, only information technology should be fairly apparent when looking into the door. Look for the bolts attaching the window itself to the mechanism that raises and lowers it.^[3]
- You may need to utilize a flashlight to look into the service ports on the door.
- Different shaped doors will place the bolts in different locations.
iv
Motion the window if necessary to access the bolts. In some cases, y'all may demand to raise or lower the window in order to access the bolts. Turn the cardinal in the ignition of the vehicle without starting the engine to move the window if need be.^[4]
- Heighten or lower the window using the power window buttons if possible.
- If the motor is broken, yous can force the window upward or down by hand.
5
Remove the bolts while a friend supports the window. Utilize the appropriate sized socket or open up concluded wrench to remove the window mounting bolts, but enquire a friend to hold the window upwards every bit you do to prevent information technology from falling down in one case it's disconnected.^[v]
- You may be able to hold the window in identify as you loosen the bolts yourself, only information technology's dangerous.
- Dropping the window freely could result in the glass breaking.
6
Raise the window up into the door frame. Have your friend enhance the window upwardly into the door frame as though you had rolled it up normally. Ask them to hold the window in place until yous are able to secure it.^[six]
- Pressing one palm on each side of the glass will allow your friend to hold the window upwardly.
7
Utilize masking tape to secure the window in place. With your friend holding the window upwards, pull off three or four strips of masking tape that are each almost a foot long. Stick the strips to the window on each side over the door frame to hold the window up while you work.^[7]
- One time the window is secured with the record, yous can have your friend let go.
- Be sure the tape will hold the weight of the window earlier your friend releases it.

1
Remove the window regulator bolts. The window regulator runs the width of the interior portion of the door and moves back and forth in social club to enhance and lower the window. Find the bolts that hold the regulator to the door and remove them with a socket or open ended wrench.^[viii]
- Set the bolts aside someplace safe, where you will hands be able to make up one's mind which bolts were for the regulator.
- Exit the regulator laying inside the door'south interior for now.
2
Locate and remove the window motor mounting bolts. The power window motor is much smaller than the regulator, but should be located close by. In well-nigh applications, the bolts securing the motor to the door are the same size equally the regulator mounting bolts. Remove them and set them someplace safe as well.^[9]
- Fifty-fifty if the bolts take the same size head, they may non be the same length, so be sure to set them aside separately from the regulator mounting bolts.
3
Disconnect the motor wiring harness connector. The power window controls attach to the motor and regulator via a wiring pigtail connector. Press the tab down to disconnect the pigtail then pull them apart to disconnect the motor.^[10]
- Exist careful not to intermission the tab that holds the wiring harness together.
- Pull the pigtail apart at the prune, not on the wires. Pulling on the wires could pull them out of the pigtail.
four
Remove the motor and regulator through the access port. With the pigtail disconnected, the ability window motor and regulator will no longer be continued to anything inside the door. Accomplish into the big access port and pull them each out.^[xi]
- The two are connected, so pulling one will remove them both.
- Be careful non to harm the regulator if you are only replacing the motor.
5
Connect the regulator to the new motor. If you are only replacing the power window motor and not the regulator itself, you volition need to disconnect information technology and connect it to your new power window motor. Visually audit the two to make sure the new motor matches the old ane, so bandy the regulator.^[12]
- Dissimilar vehicles will use different methodology to secure the regulator to the window motor.
- Refer to the service manual for your vehicle if you are unsure of how to disconnect the regulator.

Advertizing

1
Slide the new motor and regulator back into place. Insert the power window motor and regulator dorsum into the main service port in the door in exactly the opposite social club that yous removed them in when disassembling the door.^[13]
- Orient each component so the holes for the mounting bolts will line upward with the holes in the interior of the door.
2
Replace the mounting bolts. Concord each component in the advisable position as y'all return the mounting bolts that secure both the power window motor and the regulator. Thread each bolt in by hand beginning, then use a wrench to tighten them.^[14]
- If a commodities doesn't thread it properly, remove information technology and try again to forbid cantankerous-threading them.
- The bolts don't have to exist extremely tight, only tight enough to foreclose them from vibrating loose as you bulldoze.
3
Reconnect the electrical connector. Once the power window motor and regulator are both mounted securely to the door, connect the wiring from the motor to the pigtail you disconnected previously. This volition reconnect the power window switches and ability source.^[xv]
- Be sure the connections fit together. If not, you don't accept the correct power window motor.
4
Remove the masking tape and lower the window dorsum downwards. Ask your friend to agree the window once more. Once they are in place, remove the masking record that is holding the window up in the door frame. Once the record is removed, your friend can lower the window dorsum into the mounting bracket.^[xvi]
- Make certain your friend has a grip on the window before removing the record that secures it.
- You can use adhesive remover like Goo Gone on the window if the tape left any residue once you are washed.
5
Insert the window mounting bolts. Take your friend concord the window in the correct place and then the holes in line upward with the holes for the window mounting bolts. One time the window is in place, thread the window mounting bolts in by hand, before tightening them with the wrench.^[17]
- Be certain your friend holds the window in place until the mounting bolts are in place.
- Have your friend permit get gradually to ensure the bolts are belongings the window properly.
6
Reinstall the plastic liner and interior console. Once the window is mounted again, you tin can reattach the plastic interior cover, then reinstall the interior panel over the door. Insert the door mounting bolts or snaps to concord it in place.^[18]
- Once the door is reassembled, reconnect the battery.
- Commencement the engine and test the window.

Add together New Question

Question

If a regulator has a helper spring on it, do I demand to accept the whole regulator out to secure the arms, or can I replace the motor while it is in the automobile?

Depending on the design of the vehicle, you volition probable demand to remove the regulator as well as the motor when replacing it.
Question

Is the window regulator motor from a 2001 Ford Escape interchangeable with a 2002 Ford Explorer?

They might be. The best manner to know for certain is to check the part numbers for each and see if they match. If they do non, they are not interchangeable.
Question

Where is the fuse located?

The_general_s

Community Answer

Fuses are ordinarily in i of three areas: the engine bay, trunk area, almost steering bike.